CAPER VAPOR

CAPER VAPOR


All Your Vaping Needs!!

MODS
618 Pipe

Package Include:
1* Electronic cigarette pipe
2* 900 MaH batteries
1* Replacement inhaler
1* Replacement atomizer
1* Charger adapter
1* User manual


MVP 2.0

Package includes:
2x Atomizers
1x Power source
1x Cone
1x USB charging cable
1x User manual



MVP 20W

The MVP 20W is the newest in compact Variable Voltage and Wattage box mods. It has advanced safety features, a long lasting 2600mAh battery, ‘Vape while you charge’ technology and also acts as a charger for your mobile phone and other electronic devices.

Note:   Atomizer not included.  It is in the photos to demonstrate the size and look of the device.

Features of The MVP 20W 

Variable Voltage: 
Voltage can be adjusted from 3.3 – 7.5 volts in .1 volt increments.

Variable Wattage: 
Wattage can be adjusted from 6.0 – 20.0 Watts in .5 watts increments.

Battery Level Indicator: 
The MVP20W battery capacity is displayed via green, yellow and red LED.
Green = Almost fully Charged. When the MVP20W fully recharged the LED light will power off.
Yellow  = Half Power.
Red = Low Power. Charge the MVP20W.

Large battery capacity: 
The MVP20W has a built-in 2600 mAh polymer Li-Ion rechargeable battery.

ON/OFF battery switch: 
Press the power button three times in rapid succession to turn on the MVP20W. When the MVP20W is powered on Hold down the button to activate the atomizer and vape. When the MVP20W is not in use, press the button three times in succession to power off the MVP20W Advanced Personal Vaporizer. Always power off the MVP20W Advanced Personal Vaporizer when it is not being used, or when it is going to be stored in a pocket, bag or purse.

Ohms meter: 
Reads the resistance of your atomizer/cartomizer/clearomizer.

Puff Counter: 
The integrated Puff counter will record the number of puffs you have taken. Either press “P “button or “U” button for 1 second to check the number of puffs. The Puff Counter will reset to 0 whenever the device is powered off.

SAFETY: 

10 second Cutoff 
If the activation button is held for longer than 10 seconds the MVP20W Advanced Personal Vaporizer will stop firing until the button is released and pressed again.

Low Voltage Warning 
The Red LED and Battery bar will continue blinking when the battery capacity is lower than 3.3V and the MVP20W Advanced Personal Vaporizer will power off automatically.

Short Circuit/Atomizer Protection
Short Circuit/Atomizer Protection protects the MVP20W Advanced Personal Vaporizer against shorted atomizers and will stop the unit from functioning in unsafe conditions.

Over-Discharge Protection: 
The MVP20W Advanced Personal Vaporizer monitors the battery voltage and will automatically power off when the battery is discharged.

‘Vape while charging’ Technology
The MVP20W is recharged with a Micro USB cable. When plugged into a power source the MVP20W can also be vaped and charged at the same time with Innokin Technology’s ‘Vape while you charge’ pass-through technology.

Remembers last Voltage or Wattage setting
When the MVP20W is turned off it will store the current voltage or wattage setting and it will retain the setting when the MVP20W is powered on.

Built-in 3 digit display
Digital display shows the Ohms meter, Voltage / Wattage setting and the number of Puffs taken since last time the battery was turned off.

Portable power source for electronic products 
To charge your portable electronic device with the MVP20W – set the small pin switch on the bottom of the MVP20W to the ON position and connect a microUSB cable to the USB OUTPUT port (DC 5V, maximum output current 0.5A)To maximize the battery charge of your MVP20W please ensure that the bottom switch is set to the Off position when you are not using the portable charger function.
Technical Specifications: 

Operating Voltage: 3.3V-7.5 V

Operating Wattage: 6.0W-.20W

Standby current: 100uA max

Maximum output Wattage: 20W

Maximum output Current:6A

Maximum output Voltage: 7.5V

Clearomizer Resistance: 1.0 Ohm (minimum)

Battery: Built-in 2600 mAh polymer Li-Ion rechargeable battery.

Charging: Micro USB DC5V/1000mA

OUTPUT port :DC5V /1000mA

I Joy

1. variable wattage from 3W to 15W
 2. automatic identify the clearomizer's resistance, and adjust to the autofit wattage automaticly
 3.  A+/A- function. builtd in PCB board can identify the resistance of the clearomizer and automatic adjuste the wattage to the best rate.
4.  the first ecig mod with sound.when you twist the button with the transformer, it will make some merhanical sounds,which ideal from the transformers. you can say this is not just a ecig mod but also a toy for you.

Innokin Coolfire 2

- Scale Display Wattage
- Scale display wattage improves intuitive control and provides more accurate
performance.
- Variable Wattage:
- The rotational wheel adjusts wattage to the following:
7.0, 8.0, 8.5, 9.0, 9.5, 10.5, 11.0, 12.0, 12.5
- Battery Level Indicator:
- Reverse Battery Protection Circuit.
- Built in 7A fuse for protection and stability.
- Short Circuit Protection.( 0.6 +/-0.2 ohm )
- ON/OFF battery switch.
- LED Battery Power Display.
- Low Voltage Warning.
- Overtime Vaping Warning (10 seconds switch cutoff).
- Battery safety protection (Vent holes).
- High compatibility 510 connector:
Will fit iClear10, iClear16, and iClear30 clearomizers, as well as standard
510 accessories

Joyetech eVic Starter kits

1x eVic control head
1x eVic battery tube
1x rechargebale 2600mah battery
1x eVic USB cable
1x eVic wall adapter
1x eVic manual
1x MVR manual 


K1000 Epipe

Best k1000 epipe ecig

Unique epipe style

Various colors option

Big vapor k1000




Machine Gun Mech MOD


color:black,red,yellow,blue
Material:stainless steel
Use 18650 battery
Fit for all 510 EGO thread atomizer,such as CE4/CE5/CE6/VIVI NOVA, protank/MT3 etc atomizer
weight:176g 




Vamo V3

  • Variable voltage: Adjust the voltage output from 3.0 to 6.0 volts in 0.1 volt increments.
  • Variable wattage: Set the preferred wattage (from 3 to 15 watts)
  • RMS Out: RMS provides a more accurate voltage output.
  • 510 Threaded
  • Can be used with single 18650, single 18350 or two 18350 (flat top). This device is not compatible with protected batteries.
  • Atomizer resistance check
  • Battery power check
Vamo V5

Variable voltage 3.0 – 6.0V (.1 increments)
Variable wattage 3 – 15W (.5W increments)
Voltage operation selection (RMS or Mean)*
Multiple battery options (single 18650, dual 18350, single 18350)
Atomizer resistance display
Battery voltage display
eGo/510 threading (recessed)
Chrome over copper construction
Chrome over copper button
Blue OLED readout
Over/under current protection
Low resistance protection
Approximately 5 3/8″ Long and 7/8″ diameter. (Complete unit)

VNEW

1:Variable voltage: 3-6V

2:Variable power : 5-15W

3: atuto taste atomizer resistance

4: show time puffs,power

5: Charger for Iphone.

6: Intelligent control  

7:  automatic protection


Contain in package :

1:   1*Vnew body

2:   2 18650mah 2200mah battery

3:   2 atomizer (vivinova)

4:   charge

VTR

    Variable Voltage: voltage can be adjusted from 3.0 – 6.0 volts in .1 volt increments.
    Variable Wattage: Wattage can be adjusted from 3.0 – 15.0 W in .5 watts increments.
    Short Circuit Protection.
    RMS (root mean square)
    Reverse Battery Protection Circuit.
    Resistive Load Detection ( Ohms meter ).
    ON/OFF battery switch.
    LED Battery Power Display.
    Low Voltage Warning.
    Overtime Vaping Warning (10 second switch cutoff).
    Battery safety protection (Vent holes).
    High compatibility 510 connector:
    Will fit iClear 10, iClear 16, and iClear 30 clearomizers, as well as standard 510   


X6

Battery Capacity  1300mah





The NEW Dovpo E-LVT is waterproof, shock proof, you can charge your cell phone AND it's equipped with a flashlight! Be the first to own this sweet device! This is perfect for the active lifestyle.

Features:
1. Waterproof, Durable anti-fall, Anti-pressure;
2. With flashlight, Can be used as mobile power supply;
3. Variable voltage 3.0v-6.0v
4. Variable wattage 3w-15w
5. Standard 510 & eGo thread
4. Supporting 18650 batteries (unprotected)
6. Powerful bank.

DOVPO E-LVT Kit Included:
1* elvt body
3* Screws
1* L-shape wrench
1* USB Cable

ELVT 2  30W


Wattage 7W-30W

Voltage 2.5V,cannot adjust,change base on the power

Resistance >0.3ohm

Colors blue,gray,green,purple,brown,camo

Dust-proof, water resistant,IPX1

This Hana Box Mod clone is the 18650 version with DNA 30 chip. It's a 1:1 replica of the original one.

Colors are avaliable in: Black, Silver, Blue, and Orange.

Content:

  • Full sized Aluminum body
  • Custom milled display screen with a flush fit to the outside of the box
  • Fits 18650 batteries (not included)
  • Flush 510 connector
  • Flush dome style Fire Button
  • 7 - 30 watts
  • 0.3 - 3.0Ω Atomizer Resistance
  • On-board USB charging @500mA
  • Comes with the logo and a random serial number

The Everzon/ Dovpo E-MECH is a revolutionary Transformers Style E Cigarette Mod with touch screen operation, co-manufactured by DOPVO and Everzon, it accept two 18650 batteries in parallel and can be powered up to 30W.

3 Patterns available: Autobots, Deceptions and No Picture.

Voltage: 3V-6V
Wattage: 3W-30W
Colors Available: Black, Silver, Red
Material: aluminium alloy + zinc alloy

Features In Brief:
• Touch screen operation
• Variable voltage 3.0-6.0V
• Variable power 3w-30w
• Clock
• Calendar
• Alarm clock
     • Emergency flashlight

   • Power bank: current 2.1A, voltage 5V
    • Two 18650 batteries parallel connection

       The E-MECH Package Details:
     1* E-Mech Mod
   1* USB Cable
      1* User Manual
      1* Gift Package

 
Cloupor T6 Features:
1. Size: 93mm*47.5mm*30mm
2. Output power: 7W-100W 
3. 26650 battery
4. Output voltage : 3.6V—9.3V
5. Max output current: 15 Amps
6. Can be charged through USB port 
7. Can build on 0.2-4.0 ohm atomizer
8. Adjustable 510 Pin
9. IC board comes with self-heat dissipation system
10. Reverse battery protection , no worry about installing battery improperly
11. CPU temperature control system
12. Magnet back cover,no need to use screwdriver,more convenient
13. Instead of screen lock, It can be turned off
14. Colors: Black,blue,red,silver
15. Complete disconnect and installation box mod
16. Pass Through vaping while charging
17. Over charge protection: Stop charging while it is over 4.2V.
18. Battery low voltage protetion
Cloupor Mini 30W Features:
1. Size: 77.5mm*36mm*22mm
2. Output power: 7W-30W 
3. Removable 18650 battery
4. VV/VW Mode can be switched manually
5. Vaping time counting ( 15S limited protection ) 
6. Output voltage : 3.6V—7.0V
7. Max output current: 10 Amps
8. Can build on 0.45-3.0 ohm atomizer
9. Adjustable 510 Pin
10. Ohms reading calculats to 0.01ohm
11. Reverse battery protection , no worry about installing battery improperly
12. Left & Right Mode
13. Magnet back cover,no need to use screwdriver,more convenient
14. Instead of screen lock, It can be turned off
15. Over charge protection
16. Colors: Black,Silver
Cloupor T8 Features:
 
1. Size: 102mm*55mm*25mm
2. Output power: 7W-150W
3. Dual 18650 battery 
4. Magnets back cover,more convenient to take off the battery
5. Adjustable 510 Pin
6. Output voltage : 1.5V—7.6V
7. Max output current: 20 Amps 
8. Can build on 0.15-4.0ohm atomizer
9. IC board comes with self-heat dissipation system
10. Reverse battery protection , no worry about installing battery improperly
11. CPU temperature control system
12. Instead of screen lock, It can be turned off
13. Color: Black,blue,red,silver
14. Can not be charged through USB port

Cloupor ZNA50 Mod Features:

1.Chip is 100% designed by cloupor
2.Output power: 7W-50W
3.Output voltage : 3.6V—9.3V
4.It can be used to 0.3 - 3.3 ohm atomizer
5.Reverse battery protection
6.Come with 18650 and 18500 sized tube
7.Adjustable 510 pin

Luxyoun 150 W


Watts range: 7-150W (manufacturer tested)
0.79" OLED display screen show current battery voltage and output voltage, atomizer resistance, the output power, the puff and smoking for onr time
Variable wattage: Wattage adjusted from 7W-150W (in 1W increment)
Output voltage: 3.2-4.2V
The standard load is 3ohm, can work at 0.3ohm load
Static current: 4.2V/<300uA
Battery reverse connect protection
Low pressure alarm
Output short circuit protection and low impedance protection
In the ignition, can display the battery level, output voltage, output power, resistance on the screen
Join gravity sensing touch system
510 threaded connection (copper center pin)
Micro-USB charging port
Powered by single 18650 battery (battery sold separately)
 

Luxyoun Smaug 150W



100% Authentic & Genuine Luxyoun Dragon Smaug box mod is here. The manufacturer has done an amazing job, the chip is made by engineers who had left Sigelei to open their own manufacturing facility that focuses on quality first and foremost. They have made a compact mod that holds dual 18650 batteries, has copper contacts and a clean crisp OLED screen . Wattage can be changed via the Gravity Sensor or you can adjust by the button. If you have been looking for a box mod and couldn't decide which one was right for you, your search is over.Your choice of color Black, Silver, or Blue

  • Variable Wattage: 7W to 150W Wattage adjustment via gravity sensor and up / down buttons
  • Yihi SX1500 Regulated Wattage Chip
  • Supports 0.3 ohm to 5.0 ohm Atomizer
  • Battery Charge Indicator
  • Short Circuit Protection / Reverse Polarity Protection and Low Voltage Warning
  • Features a 5 click On/Off switch
  • LCD display:(resistance, voltage/wattage, settled vaping time, battery level and puffs)
  • Short circuit protection,Low voltage warning
  • Copper Contact Pin
  • Dual18650 battery (not included)
  • 510 threaded Connection Fits most atomizers
  • Comes In three colors silver, black, and blue

Tesla Invader

main feactures:

1.Battery:two of 18650 batteries           
2.Material:wood             
3.Color:black         
4.Pin:copper plated copper           
5.Thread: 510 ego thread        
6.Dimension :118.5*58.4*32mm  
7.Reverse and short protection:It has the ptc fuse inside
8.The supported resistance:0.2-3.5 Ohm
9.The output current is 12A,the maximum current can reach to 20A
10.Output voltage:3.2-4.2V

SMY GOD MOD 180W


– Aluminum Body

– Variable Voltage and Variable Wattage

– Real time Current Meter

– 5~180 WATT Maximum Output

– Sub Ohm Fires to 0.5 -4ohms

– 119X69X30mm

SMOK XPRO 50 upgradeable to 65 W


XPRO M50 is upgradable to 65W!  

Passthrough function has been added!

DOVPO DT 50


This is an aluminum flat black mod on the sides with a silver colored top and bottom that are held on by small phillips heads screws at each corner for a total of 4 screws on the top and 4 on the bottom. It also has beveled edges on every corner of the device and will not show fingerprints easily.

Specification:

1.OLED display screen

2.Working voltage:3.3-4.2V

3.Output power:5-50W(adjustable wattage)

4.Adjusted according to a load resistance of smart match
Resistance:0.2-0.3Ω power:20-50W
Resistance:0.4-0.8Ω power:15-40W
Resistance:0.9-1.4Ω power:10-30W
Resistance:over1.5Ω power:5-20W

5.Intelligent memory:retain memories of the last resistance adjustment of power parameters, recycle use the same power will 

automatic matching

6.Load capacity:minimum resistance 0.2Ω

7.Output short circuit protection

8.Low-voltage automatic protection:voltage lower than 2.5V

9.Automatic Temperature protection:temperature over 70℃(158℉)

10.Lithium battery automatic protection:battery won't discharge over 25A

11.Automatic fuse protection:voltage more than 30A

12.Built-in lithium battery capacity: 4000Mah

13.Charging voltage:Micro charger DC5V

14.Max current charging: 800mA

DOVPO Forever


This is an aluminum Variable wattage between 2.0Watts and 20Watts in 0.1 watts increments. this mod built-in18650 battery,it is over discharged、short circuit and atomizer protection.

Parameter:

Dimension: 46.0mm*35.7mm*23.4mm
Material: aluminium
Maximum current output: 5.5Am
Operating Wattage: 2.0W-20.0W
Operating Voltage: 3.0V-5.5V

Resistance Range:1.0-5.0ohm

Features:
Variable Voltage:Voltage can be adjusted from 3.0-5.5 volts in .1 volt increments
*Variable Wattage:Wattage can be adjusted from 2.0-20.0 W in .1 watts increments
*Adjustable 510 connection
*Short Circuit Protection
*Battery Voltage Detection
*Resistive Load Detection 
*ON/OFF battery switch
*Low Voltage Warning
*Overtime Vaping Warning
*Battery safety protection
*Built-in 18650 battery
*OLED Display
*Charging voltage: Micro charger DC5V 1.0A

The Dovpo GX-200 is a hybrid Mechanical Mod with built in safety protection that is capable of sub-ohming to as low as 0.2 Ohms.It has low voltage protection, over current protection, short circuit protection, reverse battery protection and Automatic temperature protection.You get a mechanical mod with all the safety of a regulated device.this mod uses two 18650 batteries in a parallel connection so this will easily last you all day on one charge.

Specification:

1. Working voltage 3.2- 4.2V

2. Max output 20A

3. Output voltage is the same as battery voltage

4. Lowest resistance 0.2ohm

5. Low voltage protection < 3. 2V

6. Over current protection > 30A

7. Two 18650 batteries parallel connection, can be charged with 

micro USB cable or 18650 charger.

8. Short -circuit and reverse connection of the battery power terminal , 

will be protected

9. The height of the connector's positive electrode can be adjusted 

by screwdriver

10. Charging voltage: Micro charger DC5V

11. Max charging current : 800mA

12. Automatic circuit -breaker triggered after 15 seconds smoking.

The iPV3 Mini by Pioneer4You is now available! This small and sleek device fits well in your hand and accepts 1x 18650 Battery. It goes up to 30 Watts and can handle down to 0.5 Ohms. The iPV Mini utilizes the YiHi SX130 chip. The chip has a memory mode which you can set your specific wattage for. The body is made of zinc alloy to give it that solid feeling. The 510 pin is spring loaded for it to adjust with your atomizers. It also includes a Micro USB for its onboard charging.

Specifications:

Output Power: 5W-30W

Output Voltage: 3V-8V

Input Voltage: 3.2V-4.5V

Output Current: 13A Maximum

Input Current: 1.3A-13A

Resistance: 0.5 ohm- 3.0 ohm